If you have a batch of scrap motors, compressors, or enameled wire you've already stripped out, and you ask a recycler “how much for motor copper”, you'll often get several different answers: some quote per whole unit, some quote on the copper stripped out, and some open by talking the price down with “that's aluminium wire”. The price of motor copper is not a fixed number — it is worked out from “copper price trend × copper yield + residual value of iron and aluminium − dismantling cost”. This article explains motor copper grades, how to estimate copper yield, whether to sell whole or stripped, how to identify aluminium wire and copper-clad aluminium, and the places where you easily lose out at settlement — all in one go. It is aimed at factories with scrap motors on hand, dismantling workshops, and recyclers just entering the trade of buying motors.
1. How many grades of motor copper are there
What the trade calls “motor copper” is not one category — it has to be split into at least four grades, each with a completely different pricing logic:1. Whole motors: motors not yet dismantled, containing a cast iron or steel plate housing, silicon steel laminated core, rotor, shaft, bearings and enameled wire windings. Bought by the unit or by the tonne; the buyer does the dismantling.2. Stators (wound cores): the housing has been removed, but the copper wire is still embedded in the silicon steel slots. Cleaner than a whole motor, but copper and iron are not yet separated.3. Motor enameled wire (also called motor raw wire or enameled copper in the trade): copper wire already pulled out of the stator, with insulating varnish on the surface — the highest-value part of a motor.4. Compressors: air-conditioner and refrigerator compressors are sealed shells with motor windings inside and residual refrigeration oil, so handling requirements differ from ordinary motors.In addition, watch out separately for two categories: one is aluminium-wire motors (the windings are aluminium enameled wire), the other is copper-clad aluminium wire motors. These two look very much like copper-wire motors but are worth far less — the most common source of disputes in motor copper trading. Before selling, work out which category your goods fall into and say so clearly when asking for quotes, so the buyer can give a reliable price.
2. Copper yield decides half the price
For whole motors and stators, the price hinges on copper yield — how much copper can be stripped out of one tonne of material.1. General rule: the copper yield of whole scrap motors commonly falls roughly between 10% and 20%, but individual variation is large, so you cannot apply a fixed ratio.2. Small motors (in fans, washing machines, power tools) usually have a low copper share, with the housing and core making up the bulk; some medium and large industrial motors have thicker and more numerous windings, but their cast-iron housings are also heavy, so the copper yield is not necessarily higher.3. Motors with cast-iron housings have a high iron weight share, which clearly drags the copper yield down; aluminium-housing motors are light, so with the same windings the copper yield actually looks better.4. Rotors are mostly cast-aluminium squirrel-cage construction and contain no copper — don't count rotor weight as “copper-bearing” when estimating.5. Compressors usually have a low copper yield because of the thick shell and the iron parts inside such as the crankshaft and cylinder.The most reliable method is sample test-dismantling: pick a few representative units from the same batch, dismantle them and weigh the copper, iron and aluminium separately, work out the actual copper yield of the batch, and negotiate on that figure. The more mixed the batch, the more samples you need.
3. Sell whole or strip first?
Many people assume “stripping it always gets more money”, but it depends on volume and labour:1. Small volume, mixed types: sell whole. Dismantling takes tools and manpower; stripping a few small motors yourself costs far more in man-hours than the extra money you get, and you easily snap the enameled wire or mix in iron filings.2. Large volume, uniform models: it is worth considering dismantling, or at least removing the housings and selling stators. Uniform models mean a fixed dismantling method and high efficiency, and the copper, iron and aluminium you strip out can each be sold by their own grade — the total usually comes out higher than selling whole.3. Keep the stripped materials separate: enameled wire in one pile, silicon steel and housing iron in another, aluminium housings and aluminium rotors in another. Sell them mixed and the buyer will price them at the lowest grade.4. Don't burn the varnish off enameled wire: under current regulations, open-air burning to remove varnish is illegal, the black smoke makes you an easy target for inspection, and the burnt copper surface oxidises, which also gets it downgraded. Selling enameled wire with the varnish on is standard practice in the trade — buyers have dedicated processing methods.5. Don't cut compressors open yourself: the refrigeration oil inside is, under current regulations, mostly managed as hazardous waste, and cutting carries safety risks — handing them to a unit with the proper handling capability is safer.
4. How to identify aluminium wire and copper-clad aluminium
The biggest trap in motor copper trading is that the wire isn't pure copper. Sellers should check beforehand, buyers should verify on site:1. Scrape the varnish and look at the colour: scrape off a short section of insulating varnish with a blade — pure copper is purplish-red, aluminium is silvery-white. The colour of the varnish itself proves nothing; both copper and aluminium wire can have yellow or red varnish.2. Look at the cross-section: cut a wire and look at the cross-section — silvery-white in the middle with a ring of copper colour outside means copper-clad aluminium. Scraping the surface alone won't show it; you must cut it open and look at the cross-section.3. Weigh it in the hand: for the same volume of wire, copper's density is roughly three times that of aluminium, so the difference in feel is obvious; an experienced hand can tell at a touch.4. Check the nameplate and the application: some low-priced small appliances and some fan motors have a higher share of aluminium wire or copper-clad aluminium; older and industrial motors have a higher share of copper wire — but these are only probabilities, and dismantling and inspection is what finally counts.5. Sample several units from the same batch: mixed loads are very common, and one copper-wire unit doesn't mean the whole batch is copper wire.Aluminium-wire motors aren't unsellable — they just have to be quoted separately as the aluminium-wire motor grade. The worst case is mixing them in with copper-wire motors and having the buyer spot it on sampling, then knocking down the price on the whole batch — you lose more that way.
5. What deductions to guard against at settlement
Once the price is agreed, there are still several places at settlement where you can lose out:1. Fix the impurity deduction rate in advance: whole motors contain oil, plastic fan blades, terminal boxes, capacitors and other debris, and buyers normally deduct for impurities. How much is deducted must be settled before weighing — ideally written into the receiving note — not discussed after the weighing is done.2. Tare weight must be weighed in person: if you deliver by truck, be present for both the empty and loaded weighings, or use a weighbridge both sides accept.3. The “varnish content” weight deduction on enameled wire: when settling varnished enameled wire, the buyer may deduct the varnish skin weight at a set ratio. Thin wire has a relatively high varnish share and thick wire a lower one, so you can ask to negotiate by actual wire diameter rather than a flat rate.4. Both sides should confirm the test-dismantling result: if you settle on copper yield, both parties should ideally be present for the sample dismantling, and the copper stripped out should be weighed and recorded on the spot.5. Make the pricing linkage clear: whether it is a flat price at that day's traded price, or a discount against some copper price benchmark, and which day's price the benchmark uses — all must be agreed in advance. When copper prices move, “which day's price” is itself a sizeable difference.6. Keep the paperwork: save the weighing slips, receiving notes and payment vouchers — you'll need them for invoicing and reconciliation later.
6. Find the right buyer and watch the market
Motor copper buyers fall roughly into three types, and each suits different grades:1. Dismantling workshops or recyclers who specialise in buying motors: the keenest buyers of whole motors and compressors, because they have the dismantling manpower and yard space — selling whole to them is the least hassle.2. Scrap copper recyclers and traders: they prefer to buy already-stripped enameled wire and have little interest in whole motors; strip first and then go to them and you'll often get a better price.3. Copper rod plants and secondary copper smelters: they generally only want copper material in large volumes and of consistent quality, and aren't too receptive to small spot lots — suited to larger dismantling plants supplying long term.When looking for buyers, you can post supply information in the supply-and-demand hall of Guilin Nonferrous Network, setting out the grade (whole motors, stators or enameled wire), approximate quantity, whether aluminium wire is mixed in, and your location, so buyers can judge; you can also use the company directory to find nearby motor-buying and scrap-copper-buying firms by category and region, and compare quotes from several directly.On watching the market: motor copper prices follow copper prices; when copper is stronger than last week, recycling quotes generally rise with it, and vice versa. Before quoting, take a look at the copper price trend on the platform so you have a reference point — then it is harder for an out-of-date quote to beat your price down.
Frequently Asked Questions
Q: Is the motor copper recycling price fixed?
No, it isn't. The motor copper price is determined jointly by the copper price trend, copper yield, the residual value of iron and aluminium, and dismantling cost. For the same tonne of scrap motors, one with a high copper yield, an aluminium housing, and no aluminium wire mixed in is clearly worth more. So when asking for a quote, say whether it is whole motors, stators or stripped enameled wire, otherwise quotes from different buyers can't be compared.
Q: How much copper can you strip from a tonne of scrap motors?
Commonly roughly between 10% and 20%, but individual variation is large. Small motors and motors with cast-iron housings are usually on the low side, and compressors are also on the low side; rotors are mostly cast aluminium and contain no copper. The most accurate method is to take a few units from the batch and test-dismantle them, weighing the copper, iron and aluminium separately, work out the actual copper yield, and then negotiate the price.
Q: Is it better to sell whole motors or strip them first?
With small volume and mixed models, sell whole: stripping them yourself costs man-hours and you easily fail to strip them clean, which gets them downgraded; with large volume and uniform models, you can consider dismantling, or at least removing the housings and selling stators, and the copper, iron and aluminium you strip out sell separately for a usually higher total. The key is that the stripped materials must be kept separate — mixed together they get priced at the lowest grade.
Q: How do you tell whether a motor is copper wire or aluminium wire?
The most reliable way is to cut a wire and look at the cross-section: all purplish-red is copper wire, all silvery-white is aluminium wire, and silvery-white in the middle with copper colour outside is copper-clad aluminium. Scraping only the surface varnish won't reveal copper-clad aluminium — you must look at the cross-section. Sample several units from the same batch, because copper-wire and aluminium-wire motors are very commonly mixed together.
Q: Can enameled wire be burned to remove the varnish before selling?
Not advisable, and not compliant. Open-air burning to remove varnish is illegal under current regulations and you easily get caught by environmental enforcement; moreover the burnt copper surface oxidises and buyers will downgrade it. Selling varnished enameled wire as it is, is standard practice in the trade — buyers have dedicated de-varnishing methods, and at settlement they generally deduct a certain varnish skin weight according to wire diameter.
Q: Can compressors be sold together as motor copper?
They can be sold, but it is best to classify them separately. Compressors have thick shells and a lot of iron inside, so their copper yield is usually lower than ordinary motors, and mixing them in drags down the valuation of the whole batch. In addition, the residual refrigeration oil in compressors is, under current regulations, mostly managed as hazardous waste, so don't cut them open and drain the oil yourself — handing them to a recycling unit with the proper handling capability is safer.
Q: What weight deductions should I watch for when selling motor copper?
Mainly three: first, the impurity deduction — plastic fan blades, terminal boxes and oil in whole motors are deducted, and the rate must be settled before weighing; second, tare weight — you must be present for the empty and loaded weighings; third, the varnish skin deduction on enameled wire — thin wire and thick wire have different varnish shares, so you can ask to negotiate by wire diameter rather than a flat rate. All agreements are best written into the receiving note.
Key Takeaways
1. Classify your goods first: whole motors, stators, enameled wire, compressors and aluminium-wire motors kept separate, and state the grade clearly when asking for quotes.2. Copper yield comes from test-dismantling, not guessing: take a few units from the batch, strip them and weigh copper, iron and aluminium separately, and negotiate on the measured figures.3. Sell whole when volume is small; with large volume and uniform models, consider stripping — and the stripped materials must be stacked separately.4. Cut the wire and check the cross-section: aluminium wire and copper-clad aluminium must be quoted separately, because if they are found on sampling in a mixed load, the whole batch gets its price knocked down.5. Before settlement, write the impurity deduction rate, the weighing method and the price benchmark date into the documents, and take a look at the copper price trend before quoting.
Further reading
- Daily nonferrous metal prices: https://www.guilinmetals.com/en/prices
- Nonferrous company directory: https://www.guilinmetals.com/en/companies
- Supply & demand marketplace: https://www.guilinmetals.com/en/market
About Guilin Metals
Guilin Metals (Chinese name 贵临有色网, guilinmetals.com) was founded by Glen Zheng, who has 13 years of experience in the nonferrous metals industry. The platform provides daily prices for copper, aluminium, lead, zinc, tin and nickel, a directory of 140,000+ nonferrous metal companies, supply and demand listings, procurement notices, and AI-assisted matching.
- Daily prices: https://www.guilinmetals.com/en/prices
- Company directory: https://www.guilinmetals.com/en/companies
- Marketplace: https://www.guilinmetals.com/en/market
*Data as of 2026-10-03.*
